Reach RS+ Green status light continually blinks

After more multiple attempts, I have managed to get the recevier working normally today. While I have access to the software, is there anything I could check to determine whether a setting is causing the issue. I fear that once I turn the receiver off, it will not work again. Thanks for any advice.

Richard,

Could you please generate the Full System Report on your unit? Please send it to me in PM as it might contain sensitive information.

Could you also clarify if at the moment the receiver has a good satellite reception?

Hi Polina
I have now been able to generate a full system report and I’ve sent this via email. Thanks.

Hi Richard,

I’ve received your Full System Report on the unit, thanks! We’ll check what could have caused the issue with the time sync.

9 posts were split to a new topic: Reach doesn’t pass the time sync

Richard,

Just wanted to give you an update on this case. We’re working on the fix for green LED behavior issue. I’ll inform you once the update is released.

If your Reacgh RS+ starts experiencing this issue again, please, reach out to me straight away.

@polina.buriak Hi Polina! my RS + started to fail, the green led started flashing. It started with version 2.23.7, before it had 2.18.1 and it always worked very well. Something is causing rechview to run internally wrong.

Luis,

Thanks for the report!

Currently, we’re working on solving this green LED behavior. I’ll reach out once there’s an update is released.

3 Likes

Hey everyone,

We’ve released the new v2.22.6 firmware update that should resolve the issues with the green LED blinking behavior. I’d ask you to update to it and check if it works for you.

To update, please go to the Updater page on your browser by typing the following to the address bar: Reach's_IP:5000. You will need to connect the device to the Wi-Fi network so that it can download the update.

Please note that the fix for this in the dev branch will be in the v2.23.9 version. We’re working on the releasing it as soon as possible. I’ll update you once it’s available.

3 Likes

Yesterday I updated the equipment, did tests and everything worked correctly. Today, the problem returned, the green led is not solid.

Hi, everyone…

Not to pile on, but I’m actually having the same problem (blinking green LED) on both our Reach RS+ units.

For what it’s worth, we hadn’t used them for some time and yesterday I broke them out to update them. I downloaded and installed 2.22.6 (I think… whichever one was available yesterday afternoon) then tested them out after that. This morning, I turned them on and they’re both blinking green with no way to connect to them.

Any suggestions? I can do a firmware flash if need be, but I wasn’t sure if there was another option.

Thank you -

@operacion @mmiller

Hello!

Do you remember the version you updated from? Do you bump into this issue every time you turn on the device?

in version 2.22.5 I had the problem, with the new version yesterday it worked, today the green led is not solid.

I believe that I was updating from Version 2.18.[something]. It had been a bit since we’d needed the units so they hadn’t been updated. This is the first time that I’ve encountered this issue.

@operacion @mmiller

Thank you for your prompt reply. Could you please tell what are the statuses of other LEDs?

If the device turns on, we’d be glad if you could share the Full System Report by sending me a private message.

1 Like

the other LEDs are solid, the green LED is never solid.
The reach viewer cannot be entered because the green led is never solid, so I cannot send the report. Before I only had that problem with the base, now my rover and base have the same problem.

1 Like

What a shame that it continues to happen with version 2.22.6

I updated to v2.22.6 as I had several start ups where the green light turned solid green after starting so I could access the software. It still worked after re-booting and I set it up for a survey the next day (yesterday). Sadly, the same issue returned and I could not carry out the survey. I tried throughout the day but the green light kept blinking. I set it up on my window sill this morning and it started correctly. Very frustrating.

I’m afraid that I’m unable to connect to either of our RS+ units through ReachView. Unless there’s another way to access the full system report, I’m going to be unable to get it.

Regarding the status lights: They’re on and solid. The green one is blinking.